How to Remove the Seat of R1200RT? (Instructions with Images!)

Front and rear seat removal, adjustment, and common challenges faced while removing the seat of BMW R1200RT are discussed in this article.

Confidently follow step-by-step instructions for both seats, incorporating tips for easy removal and re-installation.

Rear Seat Removal

Place your motorcycle on a level and firm surface and engage the stand to keep it secure.

Insert the key into the seat lock and turn it counterclockwise.

Simultaneously press down on the rear seat.

Lift the rear seat upwards and release the key.

If your R1200RT has OE Seat heating, disconnect plug 1.

Pull the seat to the rear to release it from its holders.

Installing the Rear Seat

If your motorcycle has OE Seat heating, connect plug 1.

Position the rear seat onto the holders, ensuring the tongues engage the corresponding holders.

Press down firmly at the rear of the seat until you hear an audible click, indicating a secure engagement.

How To Remove BMW R1200RT Seat

Front Seat Removal

With the rear seat already removed, proceed to lift the rear of the front seat.

For models with OE Seat heating, disconnect plug 2.

Lift the front seat upwards to detach it from the motorcycle.

Front Seat Adjustment

The front seat of your R1200RT offers customizable height adjustment, providing two different positions for your riding comfort.

Ensure the motorcycle is on a level surface with the rear seat removed.

Remove the seat supporting rod and reinsert it into the appropriate holder.

  1. Adjusting the Front Seat:
  • Following the previous step, adjust the front seat to your preferred height.
  • Ensure the motorcycle is securely placed on the stand.
  1. Installing the Front Seat:
  • If your motorcycle features OE Seat heating, reconnect plug 2.
  • Carefully push the front seat forward onto seat supporting rod 1.
  • Confirm that the seat is correctly positioned.
  • If you’re installing the seat in the low position, check that the seat’s rubber buffers engage the bottom mounts in the frame.
  • Firmly press the front seat into the mount to ensure a secure fit.
  1. Final Safety Checks:

Always exercise caution during the installation process. Avoid applying excessive pressure in the forward direction to prevent the motorcycle from being pushed off its stand. Ensure that your BMW R1200RT is stable and firmly supported at all times.

Disconnecting Electrical Components

Pressing on the back end of the lever to release it, then pulling.

Pull a little harder and wiggle while doing so, as the tab is the only thing keeping the parts together.

The little levers on connectors are hard to deal with. Proper alignment of the lever is crucial for easy disconnection, so don’t pull hard.

Our expert riders recommend spraying WD-40 into the terminals before reassembling to potentially ease the disconnection process.

Consider a cost-effective charging solution by hardwiring a plug for a Canbus charger, accessible under the seat for future charging needs.

How to install the seat on BMW R1200RT

Tips for Removing the Seat Easily

Follow the key-based seat removal process carefully. Turn the key right to remove the rear seat, then left while applying a downward force to release the front seat.

If all else fails, consider unconventional methods, like sitting on the seat, twisting the key, and tugging for a final attempt.

Note: Refer to the manual for clear instructions on front and rear seat removal.

Another method is to turn the key to the left while applying downward force on the rear portion of the front seat, allowing it to unlatch.

Some riders recommend punching down hard on the back of the rider’s seat while maintaining slight pressure on the key.

A creative solution involves rigging a thin wire or cable under the seat, allowing the rider to remove the seat by yanking on the cable while turning the key.

One rider drilled a hole in the latching arm and ran a zip-tie through it, making seat removal easier.

Another owner slipped a piece of plastic tubing over the rod part of the unlatching mechanism to push the latch pawls further open.

Some riders have opted for more permanent solutions, such as adjusting the tab activated by the key or installing a zip-tie for easy access.

Re-Installing the Seat After Removal

After seat removal, add grease to the mechanism’s touch points for smoother operation. During re-installation, avoid excessive force; the seats should click into place effortlessly.

Use pliers to adjust the tab activated by the key for better performance.

For an alternative method of seat removal without the key, consider using high-strength nylon monofilament (fishing/invisible thread).

Common Issues When Removing the Seat

Many riders experience difficulty removing the R1200RT seat, especially after it has been removed once before.

Jammed Mechanism

The consensus is to start by turning the key to the right and removing the rear seat. Then, turn the key to the left and use a combination of pushing and pulling to release the front seat.

Our experienced riders suggest pressing down hard on the seat while turning the key, which can help release any jammed mechanisms.

Front/Back Tilt Challenges

Apart from seat removal, riders also discuss challenges related to adjusting the front/back tilt of the seats.

Suggestions include using shims to raise the front or lowering the rear for a more comfortable riding position.

For those with heated seats, disconnecting the plug is a common concern. Press the tab next to the cable entry point to disconnect the plug.

Customizing Your Bike After Removing the Seat

Once the seat is removed, explore customization options for improved comfort. Consider aftermarket seats or cushions tailored to your preferences.

By following these comprehensive instructions, riders of varying skill levels can confidently navigate the BMW R1200RT seat removal process.

Always prioritize safety, adhere to manufacturer guidelines, and enjoy the seamless transition between riding and maintenance.

How to lower the seat of a BMW R1200RT?

BMW offers a Low Seat as an official accessory, providing a 1.2-inch reduction in height to 31.1 inches.

Russell Day-Long and Sargent World Sport Lower seats offer a more significant drop to 30-30.5 inches.

On the R1200RT, both the front and rear suspension can be tweaked to reduce seat height by up to 0.8 inches.

Lowering kits allow for a 30 to 40-millimeter reduction in seat height.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top