For the Honda ST1300, the engine oil capacity is 3.9 quarts (3.7 liters) without changing the oil filter, but it increases to 4.1 quarts (3.9 liters) when the oil filter is replaced during an oil change.
Use SAE 5W-40 or SAE 10W-40 viscosity fully synthetic or semi-synthetic 4-stroke motor oil that meets API service classification SH or higher for the ST1300.
Honda ST1300 Engine Oil Capacity
The engine oil capacity on the Honda ST1300 is 3.9 quarts or 3.7 liters if the oil filter is not replaced.
If the oil filter is replaced, which is recommended with each oil change, the total oil capacity is 4.1 quarts or 3.9 liters.
This is a relatively standard oil capacity for a 1300cc motorcycle engine.
How much oil does a 2007 Honda ST1300 take?
Since the ST1300 model remained unchanged throughout its production run, a 2007 model will take the same amount of oil as other model years.
With a fresh oil filter, the 2007 ST1300 takes 4.1 quarts or 3.9 liters of engine oil.
Honda ST1300 Oil Grade
Honda recommends using 5W-40 or 10W-40 viscosity fully synthetic or semi-synthetic 4-stroke motor oil that meets API service classification SH or higher for the ST1300. Synthetic oils provide superior protection and performance compared to conventional oils.
Honda ST1300 Oil Viscosity
The 5W-40 or 10W-40 viscosity grades recommended by Honda are multi-grade oils that provide viscosity characteristics suitable for a broad range of operating temperatures.
The ‘W’ refers to the oil’s performance in cold temperatures, with a lower number indicating better flow at lower temperatures.
The ’40’ refers to the viscosity at higher operating temperatures.
Honda ST1300 Oil Type
High-quality synthetic or semi-synthetic 4-stroke motor oils from major brands like Mobil 1, Castrol, and Shell Rotella that meet the API SH service classification are the recommended oil types for the ST1300.
Fully synthetic oils exceed the performance of semi-synthetic and conventional oils.
Best Oil for Honda ST1300
Fully synthetic 5W-40 or 10W-40 grade motor oils from brands like Mobil 1, Motul, and Liqui Moly that meet the API SH service rating deliver the best performance, protection, and engine longevity for the ST1300.
Synthetic oil is best for high-performance engines.
Honda ST1300 Price
Synthetic motorcycle oils meeting the Honda ST1300 recommendations typically cost $8-$12 USD per quart. For under 60$, you’ll get an oil change kit for the ST1300.
Honda ST1300 Oil Change
Honda recommends changing the engine oil and filter on the ST1300 every 8,000 miles or 12 months, whichever comes first.
More frequent oil changes such as every 5,000 miles can be beneficial, especially if riding frequently or aggressively.
Check the oil quality and quantity occasionally as a precaution.
Honda ST1300 Oil Fill Location
On the ST1300, the engine oil fill cap is located on the right-hand side of the bike, in front of the rear suspension.
A 17mm socket or wrench is needed to remove the oil fill cap to add oil.
Procedure
Remove the fairing cover and use a 17mm wrench to remove the oil drain plug and drain the oil completely.
Replace the drain plug with a new crush washer tightened to 18 ft lbs.
Use an oil filter wrench to remove the old filter. Install a new one by using a torque of 16 ft-lbs.
Add 4 quarts of Pro Honda 10W-40 grade oil through the filler hole. Start the engine and let it idle for 3-5 minutes.
Recheck the level and add additional oil to bring it to the upper mark.
Properly dispose of the old oil and filter. Reinstall the fairings securely.
Read our article on checking the oil on ST1300 to learn in detail about the oil change procedure.
Honda ST1300 Final Drive Oil Type
The ST1300 Final Drive Oil Grade Hypoid Gear Oil SAE 80 for lubrication, not regular motor oil.
The final drive capacity is approximately 27 oz or 800 ml. Honda recommends Hypoid gear oil GL4 or GL5.
Steps to Change the Final Drive Oil
Step 1: Get the Hypoid Gear Oil from the nearest Honda dealer.
Step 2: You need a 17mm wrench or sockets to loosen the plug.
Step 3: Remove the lower Drain Plug and let the oil drain completely.
Step 4: After draining, clean the drain plug and magnetic center. Inspect the Fill Plug and its O-ring for any signs of damage.
Step 5: Use a new crush washer and install the Drain Plug by applying 14 ft. lbs. of torque.
Step 6: Use a small tube over the oil container. Slide the tube into the filler hole and gradually squeeze the container. Stop adding oil once excess oil emerges from the Fill Hole.
Step 7: Complete the process by installing the Fill Plug with 9 ft. lbs. of torque.
Honda ST1300 Fork Oil Capacity
Each fork leg on the Honda ST1300 holds approximately 11.1 oz or 329 ml of fork oil.
The recommended fork oil grade is 5W or 10W viscosity.
In summary, with a new filter the Honda ST1300 takes just over 4 quarts of 5W-40 or 10W-40 synthetic or semi-synthetic 4-stroke motor oil meeting API SH standards.
Synthetic oil provides the best protection and performance in the ST1300 engine.
Honda recommends changing the oil every 8,000 miles for optimal engine life.
Honda ST1300 Oil Filter
Easy 17mm wrench-off removal using welded hex nut. ST1300 has a 0.5 lb spin-on oil filter.
How to remove the ST1300 Oil Filter?
No need to remove fairings to access the oil filter. The oil filter can be accessed easily from the right side of the motorcycle.
You can use a small strap wrench to remove the oil filter. You can install a new filter by hand tightening.
Use foil to protect exhaust and plastics from oil drips. Combine oil change with final drive fluid replacement.